● Capable of charging two batteries simultaneously ( Li-ion, Ni-MH, NiCd, LiFePO4 )
● Each of the two slots monitor and charges independently
● Identifies battery type and charges under selected mode ( except for LiFePO4 batteries )
● LCD displays charge capacity, voltage, current and time
● CC, CV and trickle charge three charge modes prolong batteries' life
● 500mA and 1000mA two charge current options
● Wide range circuit supports AC and DC dual input voltage
● 0V battery activation, auto cut-off
● Short circuit, over-current, over-voltage, reverse polarity protection
● Certified by CE, FCC, UL, CUL, PSE, GS, SAA, CB and RoHS
Input: AC 100 - 240V ( max 350mA ) / DC 12 - 24V ( max 1000mAh )
Output: 4.2V / 3.7V / 1.5V, 500mA / 1000mA
Caution: batteries are not included.Specification
Charging Cell Type: LiFePO4,Lithium Ion,Ni-MH,NiCd
Rechargeable Battery Qty: 2
Input Voltage: AC 100
240V 50/60HZ,DC 5V
Output Voltage: 4.2V / 3.7V / 1.5V
Charge Control Methods: CC (Constant-current),CV (Constant-voltage),Trickle Charge
LCD screen: Yes
Circuit Detection: Yes
Protected Circuit: Yes
Reverse Polarity Protection: Yes
Over Voltage Protection: Yes
Short Circuit Protection: Yes
Over Charging Protection: Yes
Dimension and Weight
Product weight: 0.178 kg
Package weight: 0.344 kg
Product size (L x W x H): 14.50 x 7.50 x 4.00 cm / 5.71 x 2.95 x 1.57 inches
Package size (L x W x H): 15.50 x 16.50 x 5.00 cm / 6.1 x 6.5 x 1.97 inches
Package Contents: 1 x HXY-H2 Battery Charger, 1 x US Plug Charger, 1 x Car Charger, 1 x English Manual
You Might Also Consider
Please note: the standard and expedited shipping costs are only estimates; the actual shipping price will be shown on the order page.72 Hour Price Protection Program
At Gearbest we work hard to ensure we can offer our customers high quality products at the lowest possible price. If you purchase a Gearbest product and find that the price has dropped within 72 hours of paying the order, we will refund the difference - no questions asked. Simply contact our Customer Service team at our Support Center with the details. Please note that our 72 hours Price Protection Program does not apply to Flash Deal products.
Prices may fluctuate due to page caches, updates or sales ending; the most up-to-date price takes priority.
I didn’t have high expectations with this charger. It seemed like yet another anonymous charger with no branding. So I decided to crack it open just to see how crappy it was
Very simple PCB with very few components. I immediately recognized the chips marked “57b7” as the TP4057 also found in the excellent ML-102 charger/powerbank. I thought that if this charger performed anything like the ML-102 then it would be a pretty good charger! So I decided to dig deeper…
Test cell is the Sanyo UR18650FM 2600mah. Not a perfect CC/CV but still pretty good! The CC part is in fact flatter than the ML-102, but then again this operates at lower current.
Termination current is most likely 50ma. Again my loose sampling interval probably missed it.
This particular sample terminates at 4.21v, still within tolerable limits.
Well I’m not HKJ but I think it’s safe to say that this charger is pretty good 8)
Edited by: sb56637 on 06/25/2015 - 14:19
Picture below is bottom part of the case with the AC plug in close position
Picture below is another shot of bottom part of the case with the AC plug in close position
Picture below is bottom part of the case with the AC plug in open position
Picture below; bottom part of case with AC connector close position; top half of case with the circuit board and the AC prongs contact flat folded metal spring at the left and middle part of the picture.
The IC used in this circuit is the LM324 on the lower part and right side of the circuit board
Picture below shows folded metal spring contact for internal side of AC plug. There is no protection insulation separating the two AC contact points.